Condec PIN7010 Manuale Utente

63258PIN7000 & PIN7010Portable & Rack-mountable Pneumatic High Pressure Intensifier ConsoleOperation and Maintenance Manual CONDEC Sales Phone

6 PIN7000/PIN7010 Operation and Maintenance ManualFigure 3-1. PIN7000/PIN7010 Wiring Diagram3.2.1 Panel/Chassis Removal and InstallationPIN7000 Remova

Maintenance & Service 72. Gently place panel/chassis assembly into enclosure. Ensure that the wire harnesses do not catch and snag.3. Align mounti

8 PIN7000/PIN7010 Operation and Maintenance Manual1. Secure the valve body by its center portion, in a bench vise, with the valve knob pointing upward

Maintenance & Service 93.2.5 Accumulator, Intensifier and MPV Valves, Panel InstallationTools required: 7/16" open end wrenchPhillips screwdr

10 PIN7000/PIN7010 Operation and Maintenance Manual5. Check to see that the knob insert (6) is securely fastened to the valve shaft (3). If it is loos

Maintenance & Service 113.2.8 Accumulator Assembly, O-ring (PN 58051) Replacement, Filter (PN 56993) CleaningTools required: Phillips screwdriver5

12 PIN7000/PIN7010 Operation and Maintenance ManualDisassembly Rings and Seals:1. Remove intensifier assembly from PIN7000/PIN7010 per Section 3.2.2 o

Maintenance & Service 132.11.Thread “AN” side of inlet check valve fitting (12), sub-assembly into Fitting Holder Tool (PN 70710). Now place sub-a

14 PIN7000/PIN7010 Operation and Maintenance Manual3.2.10 Regulator (Standard Pneumatic) and Solenoid Removal Solenoid 120 VAC input - PN 56851, Solen

Maintenance & Service 156. Install panel/chassis assembly in its enclosure as described in Section 3.2.1 on page 6.3.2.12 Panel Gauge Removal and

16 PIN7000/PIN7010 Operation and Maintenance Manual3. Loosen and remove the tubing end nut from the reducing tube fitting (PN 59830).NOTE: Use PN 5404

Maintenance & Service 17Input Port Filter Removal1. Vent any remaining gas from the system to atmosphere. Disconnect the power cord from the power

18 PIN7000/PIN7010 Operation and Maintenance Manual3.2.18 Panel Mounted AC Power/EMI Line Filter (PN 58870), Removal and InstallationNOTE: See Figure

Maintenance & Service 19120 VAC input - PN 56679, 220 VAC input - PN 56682Tools required: Phillips screwdriverFlat blade screwdriver (small)11/32&

20 PIN7000/PIN7010 Operation and Maintenance Manual

Maintenance & Service 213.4 Intensifier Assembly Parts ListTable 3-3. Intensifier Parts ListRef NumberPN Description Quantity1 59328Screw, cap, so

22 PIN7000/PIN7010 Operation and Maintenance ManualFigure 3-2. Intensifier Exploded ViewFigure 3-3. Standard Pneumatic Regulator Mounting

Model Number System 274.0 Model Number System P I N 7 0 0 0 - ____ ____

© 2005 Rice Lake Weighing Systems. All rights reserved. Printed in the United States of America. Specifications subject to change without notice.Versi

28 PIN7000/PIN7010 Operation and Maintenance Manual5.0 Options, Replacement KitsThere are numerous replacement part numbers mentioned throughout manua

Specifications 296.0 SpecificationsOperating Temp: +40° to +122°F (+4.4° to +50.0° C) Storage Temperature: 0° to +185° F (–17.8° to +85°C)Pressure Med

30 PIN7000/PIN7010 Operation and Maintenance Manual7.0 PIN7000/PIN7010 Warranty and Return PolicyIf possible, please save original packing material wh

PIN7000/PIN7010 Warranty and Return Policy 31PIN7000/PIN7010 Return Material Authorization FormThe repair lab is also equipped to do calibrations on o

Introduction 1About This ManualThis manual is intended for use by service technicians responsible for installing and servicing PIN7000/PIN7010pressure

2 PIN7000/PIN7010 Operation and Maintenance ManualIn addition to the features, the PIN7000/PIN7010 pressure intensifier is easy to use. Two MPV style

Operation 32.0 Operation2.1 Optional External Pressure Cylinder (PN 59533) Filling ProcedureNOTE: Condec strongly recommends that the external nitrog

4 PIN7000/PIN7010 Operation and Maintenance ManualFigure 2-1. Initial Setup/OperatingNOTE: PIN7000 shown, AC Input (1), Test Port (9) and Input Port

Maintenance & Service 53.0 Maintenance & ServiceThis section outlines the mechanical and basic electrical repair procedures for the PIN7000/PI